Thursday, August 19, 2010

Multi-LNB Satellite Dish


11:37 PM |


This guide explains how to setup a Multi-LNB Satellite dish for viewing multiple satellites on one dish. The best way to install them: setup center one first, then install side LNBs.

Before you start to put dish up, Make sure the mast is plumb and perfect vertical all around.

This Multi-LNB Mount can connect up to 6 LNBF or more in order receive 2 or more different satellite signals on one single dish. Set up center LNB first. Make sure that right LNB and correct receiver setup for match up what you are trying to get.

This Mount can hold all kind of the LNBF.
Compatible with 30mm or 40mm LNBF
you can get 4 axes point’s adjustments: forwards/backwards, up/down, left/right, side to side.

How to setup 101,110, 119 in one dish Using the Mount
The mounts that hold the Lnbf are from 1/2" to 2" emt pipe clamps/mounts. With this kind of setup ( Mount) you can get 4 axes point’s adjustments: forwards/backwards, up/down, left/right, side to side. The quality for 110 will get from 90% to 100% , For 119 will get 80% to 98% and for 121 will get 70% to 95% depending on the transponder and your receiver. But you would need to play with 119 to get the best quality you can for the both 119 and 121. With this kind of setup should get 82, 91, and 97 on one dish too.

Connect all 3 Lnbf to Super Mount. Now move it so it is about 1/2 inch higher than the first. Move it so it is about 1/2 inch higher than the second. The 1/2 inch does not have to be exact, but fairly close. Mount has Ruler mark. Hopefully, between reading and looking at the pictures, you'll make it work. First time setup took quite some time to get it figured out.

The LNB on your right will be looking at Sat. 101, the middle one 110, and the left one
Will be 119. Mount the LNBF back to a dish. Mount the middle one to dish just like normal. As for tuning, hooked up DirecTV to the 101 LNB and tuned it till had signal. You could also hook up DISH to the 119 LNB and tune it in. Once you have one of them working, the other two LNBF WILL be seeing signal at its respective Sat. You will probably have to compromise on signal strength depending on where you are and what you are watching.

This is working for Dishnet110, 119, 121 too. But, between 119 and 121 will more close and almost on the same level.

This is working for BEV 82, 91, 97 too.

We can add more mount finger in order we can add more LNB to dish and receive more satellite in one dish. For example, we can put Dish net 110,119,121, Bell 91 together. Or combine with FTA LNB and receiver DSS satellite and FTA satellite together.

How to setup 82, 91, and 97 in one dish (super Dish) by using Mount


Is what you need.....
A: 33”, 36” or 39” inch dish

B: 2 DSS DN circular Lnbf -LNBF. 1- ku-linear Standard LNBF Using the LNBF will work the easiest.

C: 1- Super Mount I or Magic Mount III

D: Measuring device. I used a tape measure. A ruler that can measure out 1/2 inch. (Mount already mark the ruler on the holder)

setup same as ----How to setup 110, 119, 121 in one dish (supper Dish) by suing Mount

We should able setup 110, 119, 121, 91 in one dish by using Magic Mount

We should able setup 110, 119, 121, 91, 97 AMC4 in one dish by using Magic Mount

We should able setup T5, G3C, G13, AMC4 in one dish by using Magic Mount

More, More setup we should able fulfill by Magic Mount



All LNBF can be adjusted up, down, forward, backward, left and right.


It should let your 24"X 27" dish as SUPPER DISH.
It should let your 33" or 39" dish as T55, T90.
It should let DSS, FSS and FTA satellite locate in one dish.
More and more.....

Leave A Comment